MERCURY ADSORBENTS Product Data - NUSORB® CR

new button

Would you like to tell us more about your inquiry?

Product Data - NUSORB® CR

SULFUR COMPOUND REMOVAL
FROM: Air, Inert Gas, CO2, Hydrocarbons: Gas & Liquids
                                                       
BENEFITS             
• Meet Hydrocarbon Product Specs.
• Removes wide range of S-cpds
• Clean, Low ∆P Operation
• Cyclic or NonRegen. Systems


PERFORMANCE FEATURES
• High Removal Efficiency
• No Need for several adsorbents
• Hard, Low Dust Pellets avail. in several sizes
• Product is Regenerable; can operate NonRegen.

PROPERTIES, TYPICAL

 Steam-Activated pellet diameters

1.0mm,1.5mm,3mm,or 4mm

 Surface Area, substrate, N2 BET method

1,000 m2/g (by N2 BET test method)

 Impregnant

 Proprietary Metal Oxide Removes a wide range of sulfur compounds 

 Packed Bulk Density (ASTM D2854)

30 to 34 Lb/Ft3 (480 to 545 kg/m3)

 Moisture Content (ASTM D2867)

5 wt. %, max, as packed

 Hardness (ASTM D3802)

98 %

 Ash (ASTM D2866)

15 wt.%

 Packaging

150 Lb Sq. Fiber Drums; 1,000 Lb Bulk Bags


APPLICATIONS
NUSORB® CR adsorbent has proven performance for removing H2S, CS2, light mercaptans, i-Propyl mercaptan, t-Butyl mercaptan, sulfides, disulfides, COS, SO2, and H2Se (hydrogen selenide) from gases including 100% CO2 gas, and from hydrocarbon liquids. This adsorbent was specially developed for removing sulfur compounds from streams that do not contain oxygen, but it also works well in air. Maximum adsorption capacity for removal of sulfur compounds from hydrocarbon or inert gases, is 3 wt.%, as S. This adsorbent can be regenerated by superheated steam at 300-400 °C, followed by a N2 + O2 sweep to reactivate the impregnant to its active form. The steam cycle removes recoverable sulfur from the carbon. The impregnant in NUSORB® CR adsorbent is non-corrosive.

Providing Solutions to remove mercury for emission control, corrosion prevention and catalyst protection.



Selective Adsorption Associates, Inc. (SAA) offers over 40 years of experience in Process Engineering of Adsorption Systems for Gas and Liquid Drying, Sulfur Compound Removal, Emission Control, and over 20 years of Process Design experience in Mercury Removal Systems.

CAUTION: Wet activated carbon removes oxygen from air. Thus, an asphyxiation hazard exists inside enclosed spaces containing activated carbon. Use appropriate safety precautions when entering vessels or other enclosed spaces containing activated carbon. Exposure to strong acids and oxidizers can cause formation of toxic H2S gas.

MERSORB® is a trademark of Nucon International, Inc. (NUCON®) for impregnated activated carbons used to remove mercury from gases and liquids. NUSORB® is a trademark of NUCON for its activated carbons. Information presented herein is believed to be accurate and reliable but does not provide any guarantee or warrantee by NUCON® or by Selective Adsorption Associates, Inc. Nothing herein shall be construed as an invitation to use processes covered by patents without proper arrangements with individuals or companies owning those patents.

AntiMercure® is a Registered Trademark of Selective Adsorption Associates, Inc. (SAA) for its Process for removing mercury from water; AntiMercure™ is a trademark of SAA for its pre-Engineered Systems for removing mercury from water. All Rights Reserved.


REPORTS

MERSORB®

The high performance mercury adsorbent products for gases and liquids.

Read More

Sales & Service Contact:

ADDRESS
Selective Adsorption Associates Inc.
41 University Drive
Suite 400, Newtown, PA. 18940 USA.
TELEPHONE
+1 215 702 0323
FAX
+1 215 702 0577
E-MAIL
sales@antimercure.com
NEWSLETTER
Subscribe To Mailing list